TANNOY Vnet™ 12HP ลำโพง Series - Active, DSP enabled & networkable

The high power handling, point source, constant directivity PowerDual™ drive unit in the VNET12 HP integrates with leading edge digital signal processing, network control and Class D amplifier technologies to create sound reinforcement loudspeakers designed to form the complete installation solution.

By taking the modular approach, where all the main system elements are designed into each loudspeaker, the amplifiers, processing, monitoring and drivers have all been optimised to perform as a unified whole. The resulting package of intuitive user setup, integrated processing, tuning control, performance diagnostics and protection produces an exceptionally high performance networkable loudspeaker that is easy to install.

VNET™ supports free network topology so cabinets can be arranged in a daisy chain, linked in a star configuration or in any combination of both. Implementation of the network could not be simpler, with connections between nodes via high quality rugged Neutrik Ethercon connectors, which are compatible with standard RJ45 plugs, and CAT5 cable. Each VNET™ module contains a unique address so that no user input will be required to configure network nodes.

System commissioning and ongoing venue network control, incorporating real time diagnostics of electronics and drive unit, are all managed by the exclusive VNET™ software package. Supplied with each unit, this intuitive Windows tool controls all of the critical install, commissioning and performance monitoring functions.

A standard wireless LAN-to-serial bridge can be used to communicate with the network, allowing the commissioning engineer to sit in the auditorium communicating from a laptop on 802.11b

Specifications

• VNET12 HP
• PERFORMANCE
• System Type    Full Range - vented
• Frequency Response +/- 2dB (1)    65Hz - 23Hz
• Maximum SPL    Program: 124dB
• Peak: 130dB
• Dispersion (-6dB)    75 degrees conical
• Crossover (DSP Generated)    1.7kHz and variable high pass filter for use with subwoofers
• DRIVE UNIT
• DSP SECTION
• Comms Facilities    All parameters editable, firmware updatable
• Communications    Serial - RS485 Proprietary message format
• Dynamic Range    112dB(A) typical
• DSP    3rd generation SHARC
• Sampling Frequency    96kHz 24 bit A/S-D/A word length
• Format    1 IN - 2 OUT
• PSU SPECIFICATIONS
• Input Connector    Locking Neutrik Powercon
• Voltage Selection    Automatic 45 - 65Hz
• Switching Frequency    192kHz Syncronised to DSP
• Input Voltage    115/230V +10/-20%
• ELECTRONICS
• Efficiency    >85% typically
• Damping Factor    120 ref 8 Ohms
• Distortion    <0.05% @ 1kHz -3dB output (22kHz bandwidth)
• Input Impedance    Unbalanced: 5.6kOhms
• Balanced: 11.2kOhms
• Output Power (programme)    700W LF
• 700W HF (limited)
• Input Sensitivity    1.4V (+5.5dBu)
• System Type    Dual channel Class D
• CONSTRUCTION
• Enclosure    37.5 litre vented
• 15mm (0.62") birch plywood enclosure
• 15mm (0.62") MDF front baffle
• Black perforated steel grille
• Connectors    1 x female XLR (input)
• 1 x RJ45 (network in)
• 1 male XLR (link)
• 1 x RJ45 (network link)
• 1 x Neutrik Powercon
• Fittings    1 x recessed carrying handle (rear)
• Blanking plate for optional VTH pole mount
• 8 x M10 flying mount inserts
• 1 x Pull back point
• Dimensions (HxWxD)    486 x 370 x 360mm
• (19.13 x 14.57 x 14.17")
• Weight    29kg
• (64lbs)
• Finish    Textured black or white paint