LAB GRUPPEN C 5:4X เพาเวอร์แอมป์ High continuous output power of 125 W per channel at 70 V, 4 ohms, 8 ohms, and 16 ohms เครื่องขยายเสียง
• Four channels in 2U - High channel density reduces space
requirements and installation time
• High continuous output power of 125 W per channel
at 70 V, 4 ohms, 8 ohms, and 16 ohms*
• All channels individually selectable for lo-Z or hi-Z
Loudspeakers (2 ohm – 16 ohm) and distributed systems can be
connected to the same unit
• Bridged operation – Channel pairs bridgeable for increased
output or for driving 100 V systems
• Patented output stage based on Class D topology
• High efficiency for lower thermal stress
• General Purpose Input/Output (GPIO) – Compatible with
third-party control systems
• NomadLink® network ready
• Universal Power Factor Corrected PSU with IEC inlet
• Efficient cooling – Dual variable speed, intelligent fans and
parallel airflow over output devices provide uniform cooling
• Comprehensive circuit protection and fault indication
• Phoenix-style input connectors and barrier strip output
connectors
An Installation Amplifier without Compromise
Lab.gruppen amplifiers have earned an enviable worldwide reputation for sonic excellence and rock-solid durability in touring sound applications. These same qualities are now available for a broad range
of installed sound applications in the C 5:4X amplifier. By offering an
unmatched combination of channel density, operating efficiency and
configuration flexibility, the C 5:4X presents convincing performance
and cost-saving advantages. Applications include primary systems
for theme parks, shopping malls, airports, hotels and restaurants as
well as auxiliary systems for performance venues, houses of worship
and numerous other installed sound applications.
To achieve higher channel density without compromising performance, Lab.gruppen engineers developed a new output stage
design. Based on a patented Class D circuit topology, these output
stages produce sustained high power levels with very low distortion
while maintaining efficiency levels of near 90%. A new universal
switching power supply employs Power Factor Correction (PFC)
to stabilize current draw, and it accepts any mains voltage from
100 – 240 V (+/- 10%) @ 50 Hz or 60 Hz through the appropriate
IEC cord.
The C 5:4X includes include unique features which enable each unit
– or even each channel – to be configured for a specific application
or load condition. Input gain is selectable in two-channel groups, and
a 35 Hz high pass filter may be inserted. All channels are bridgeable
in pairs, and Lab.gruppen’s exclusive Voltage Peak Limiter (VPL) feature allows each channel to be individually optimized for the reactive
characteristics of the connected load.
For comprehensive remote monitoring and control, the C 5:4X
includes NomadLink® network ports for connecting to an optional
NLB 60E NomadLink® Bridge & Network Controller and an Ethernetlinked PC. With NomadLink®, key amplifier parameters are displayed
via DeviceControl software, and remote control of channel mute
and power on/off is under network control. Alternatively, the GPIO
facilities allow access to key amplifier functions via third-party
remote control systems.
To ensure a long and trouble-free service life, the C 5:4X incorporates
extensive features to safeguard internal circuits and connected loads.
Protection and warning circuits prevent damage or service interruptions due to excessive current, DC at output, over-temperature,
non-musical VHF (very high frequencies), and open load conditions.
In addition, soft-start and PSU current limiting protect the mains
supply from interruptions due to tripped circuit breakers or blown
mains fuses.
Specifications C 5:4X
General
Number of channels 4
Peak total output all channels driven 500 W
Peak output voltage per channel 100 V / 70 Vrms
Max. output current per channel 5.6 Arms
Max. Output Power 16 ohms 8 ohms 4 ohms 2 ohms Hi-Z
Per ch. (all ch.’s driven) 125 W 125 W 125 W 60 W 125 W (70 Vrms / 100 V peak)
Bridged per ch. 250 W 250 W 125 W n.r. 250 W (140 Vrms / 200 V peak)
Performance with Gain: 32 dB and VPL: 100 V
THD 20 Hz - 20 kHz for 1 W <0.1%
THD at 1 kHz and 1 dB below clipping <0.05%
Signal To Noise Ratio >112 dBA
Channel separation (Crosstalk) at 1 kHz >70 dB
Frequency response (1 W into 8 ohms) +0/-3 dB 2.3 Hz - 56 kHz
Input impedance 20 kOhm
Input Common Mode Rejection, CMR 50 dB
Output impedance @ 100 Hz 48 mOhm
Voltage Peak Limiter (VPL), max. peak output
VPL, selectable per ch. 3) 100, 63, 45, 32 V
VPL, selectable when bridged 3) 1) 200, 126, 90, 64 V
Voltage Peak Limiter mode (per ch.) Hard / Soft
Gain and Level
Amplifier gain selectable (all channels) 1)
– rear-panel switches 29, 32, 35, 38 dB
Default gain 32 dB
Level adjustment (per ch.) Front-panel potentiometer, 21 position detented from -inf to 0 dB, hidden behind security panel/dust filter grille
Connectors and switches
Input connectors (per ch.) 3-pin Phoenix, electronically balanced
Output connectors (per ch.) Barrier strip 2-pole screw terminals
Output bridge mode A+B and/or C+D, inputs A and C are signal source
High pass filter Fixed at 35 Hz, switchable per channel
NomadLink® network On board, 2 x RJ45 connectors, IN and OUT
Intelligent fans (on/off) Yes, depending on presence of output signal
Power on/off and Remote enable on/off Individual switches on front-panel
Cooling Two fans, front-to-rear airflow, temperature controlled speed
General Purpose Outputs (GPO) Contact Closure types, 2-pole Phoenix
General Purpose Inputs (GPI) Contact Closure types, 2-pole Phoenix
Front-panel indicators
Common NomadLink® Network; Power Average Limiter (PAL) 2); Power on
Per channel Signal present / High-impedance; Voltage Peak Limiter (VPL); Current Peak Limiter (CPL):
Very High Frequency (VHF); High temperature; Fault; Mute
Power
Operating voltage, 230 V / 115 V nominal 100-240 V
Minimum power-up voltage, 230 V / 115 V 80 V
Power Average Limiter (PAL) 2) Yes
Soft start / Inrush current draw Yes / max. 5 A
Mains connector IEC Inlet / NEMA 5-15P
Dimensions (W/H/D) W: 483 mm (19”), H: 88 mm (2 U), D: 343 mm (13.5”)
Weight 8.5 kg (18.75 lbs.)
Finish Black painted steel chassis with gray painted steel front
Approvals CE, ANSI/UL 60065 (ETL), CSA C22.2 NO. 60065, FCC