LAB GRUPPEN เพาเวอร์แอมป์ FP 10000Q เครื่องขยายเสียง กำลังวัตต์สูง delivers a total of 10000 W (4 x 2500 W @ 2 ohms) in only 2U
A Benchmark For Touring Amplification
Over the past decade, the tight and transparent sound of
Lab.gruppen touring amplifiers has earned the praise of renowned
FOH engineers and leading sound rental companies worldwide.
FP 10000Q, the flagship four-channel model of the FP+ Series, continues this tradition. At the core of the FP 10000Q’s performance
is the patented Class TD output stage, a breakthrough amplifier
topology that approaches the exceptional efficiency of Class D while
retaining the sonic purity of proven Class B designs. Further contributing to the remarkable efficiency of the FP 10000Q is a Regulated
Switch Mode Power Supply (R.SMPS), which gives the added benefit
of stabilizing rail voltages to the output even with wide fluctuations of
mains voltage. A highly refined and updated circuit layout optimizes
the interaction of R.SMPS and Class TD to produce the extraordinary
power density of the FP 10000Q.
To keep its cool under extreme demands, the FP 10000Q relies on
Lab.gruppen’s proprietary Intercooler®. This innovation uses thousands of copper fins to multiply the exposed heatsink surface’s
rapid heat dissipation. Also, all output devices are mounted transverse to the airflow for uniform cooling. As a result, the FP 10000Q
delivers Lab.gruppen’s’ trademark “all the power, all the time” with
no degradation of sonic performance.
To maximize headroom in any application, the FP 10000Q offers
adjustable input gain along with Lab.gruppen’s exclusive Voltage
Peak Limiter (VPL). Adjustable on a per-channel basis, VPL optimizes
the output for any load, from a single massive subwoofer to a series
of HF compression drivers.
The comprehensive warning and protection features on the
FP 10000Q safeguard output circuits and connected loads while
also extending amplifier life and minimizing chance of service interruptions. Whether it’s a matter of faulty wiring, improper use, or
extreme ambient temperatures, the FP 10000Q gives clear indication of any problems. Automatic protection measures engage only
at critical thresholds. Operating conditions are re-checked every
six seconds and, if a fault is detected, normal operation is resumed
when measurements return to nominal.
The FP 10000Q is shipped with a NomadLink® network interface as
standard. In conjunction with DeviceControl software, NomadLink®
allows monitoring of all key amplifier parameters and remote control of power on/off, channel mutes, and channel solo functions.
(NomadLink® requires the separate NLB 60E NomadLink® Bridge &
Network Controller).
Specifications FP 10000Q
General
Number of channels 4
Peak total output all channels driven 10000 W
Peak output voltage per channel 150 V
Max. output current per channel 38 Arms
Max. Output Power 2 ohms 4 ohms 8 ohms 16 ohms
Per ch. (all ch.’s driven) 2500 W 2100 W 1300 W 660 W
Bridged per ch. - 3) 5000 W 4200 W 2600 W
Performance with Gain: 35 dB and VPL: 150 V
THD 20 Hz - 20 kHz for 1 W <0.1%
THD at 1 kHz and 1 dB below clipping <0.05%
Signal To Noise Ratio >112 dBA
Channel separation (Crosstalk) at 1 kHz >70 dB
Frequency response (1 W into 8 ohms) +0/-3 dB 6.8 Hz - 34 kHz
Input impedance 20 kOhm
Input Common Mode Rejection, CMR 45 dB
Output impedance @ 100 Hz 56 mOhm
Output slew rate into 8 ohms 20 V/microsecond
Voltage Peak Limiter (VPL), max. peak output
VPL, selectable per ch. 150, 121, 101, 83, 70, 56, 47, 38 V
VPL, selectable when bridged 1) 300, 242, 202, 166, 140, 112, 94, 76 V
Voltage Peak Limiter mode (per ch.) Hard / Soft
Gain and Level
Amplifier gain selectable (all channels) 1)
– rear-panel switches
23, 26, 29, 32, 35, 38, 41, 44 dB
Default gain 35 dB
Level adjustment (per ch.) Front-panel potentiometer, 21 position detented from -inf to 0 dB
Connectors and Switches
Input connectors (per ch.) 3-pin XLR, electronically balanced
Output connectors (per ch.) Neutrik Speakon or Binding Posts (must be specified upon order)
Output bridge mode A+B, C+D - Ch.’s A and C are signal input source
NomadLink® network On board, 2 x RJ45 EtherCon connectors, IN and OUT
Intelligent fans (on/off) Yes, depending on presence of output signal
Power on/off and Remote enable on/off Individual switches on front-panel
Cooling Two fans, front-to-rear airflow, temperature controlled speed
Front-panel indicators:
Common NomadLink® Network; Power Average Limiter (PAL) 2); Power on
Per channel Signal present / High-impedance; -20 dB, -15 dB, -10 dB and -4 dB output signal;
Voltage Peak Limiter (VPL); Current Peak Limiter (CPL): Very High Frequency (VHF); High temperature; Fault; Mute
Power
Operating voltage, 230 V / 115 V nominal 4) 130-265 V / 65-135 V
Minimum power-up voltage, 230 V / 115 V 171 V / 85 V
Power Average Limiter (PAL) 2) Yes
Soft start / Inrush Current Draw Yes / max. 5 A
Mains connector 230 V CE: 16 A, CEE7; 115 V ETL: 30 A Twist lock
Dimensions (W/H/D) W: 483 mm (19”), H: 88 mm (2 U), Overall D: 396 mm (15.6”), Mounting D: 358 mm (14.1”)
Weight 12 kg (26.4 lbs.)
Finish Black painted steel chassis with black painted steel / aluminum front
Approvals CE, ANSI/UL 60065 (ETL), CSA C22.2 NO. 60065, FCC