LAB GRUPPEN เพาเวอร์แอมป์ FP14000 delivers a total of 14000 W (2 x 7000 W @ 2 ohms) in only 2U. เครื่องขยายเสียง กำลังวัตต์สูง
A Benchmark For Touring Amplification
Over the past decade, the tight and transparent sound of Lab.gruppen
touring amplifiers has earned the praise of renowned FOH engineers
and leading sound rental companies worldwide. FP 14000, the new
flagship model of the FP+ Series, advances this tradition by further
augmenting effective power output to effortlessly handle extreme
low-frequency loads. The Regulated Switch Mode Power Supply
(R.SMPS) has been updated to provide more sustained high power
during extended bursts of low frequency content, while at the same
time ensuring stable rail voltages even with wide fluctuations of external mains voltage. The forceful, high-current (83 A peak) output stage
relies on Lab.gruppen’s patented Class TD topology, a breakthrough
in amplifier technology that approaches the efficiency of Class D
while retaining the sonic purity of proven Class B designs. A highly
refined and efficient circuit layout further optimizes the interaction of
R.SMPS and Class TD to produce the unprecedented power density
of the FP 14000.
To keep its cool under extreme demands, the FP 14000 relies on
Lab.gruppen’s proprietary Intercooler. This innovation uses thousands of copper fins to multiply the exposed heatsink surface’s rapid
heat dissipation. Also, all output devices are mounted transverse to
the airflow for uniform cooling. As a result, the FP 14000 delivers
Lab.gruppen’s’ trademark “all the power, all the time” with no
degradation of sonic performance.
To maximize headroom in any application, the FP 14000 offers
adjustable input gain along with Lab.gruppen’s exclusive Voltage Peak
Limiter (VPL). Adjustable on a per-channel basis, VPL optimizes the
output for any load, from a single massive subwoofer to a series of
HF compression drivers.
The comprehensive warning and protection features on the
FP 14000 safeguard output circuits and connected loads while also
extending amplifier life and minimizing the chance of service interuptions. Whether it’s a matter of faulty wiring, improper use, or extreme
ambient temperatures, the FP 14000 gives clear indication of any
problems. Automatic protection measures engage only at critical
thresholds. Operating conditions are re-checked every six seconds
and, if a fault is detected, normal operation is resumed when measurements return to nominal.
The FP 14000 is shipped with a NomadLink network interface as
standard. In conjunction with DeviceControl software, NomadLink
allows comprehensive monitoring of amplifier status (including fault
or warning indications) and also enables remote control of power on/
off, channel mute, and channel solo functions. NomadLink is compatible with popular third-party control platforms; a separate NLB 60E
NomadLink Bridge & Network Controller is required
Specifications FP 14000
General
- Number of channels 2
- Peak total output both channels driven 14000 W
- Peak output voltage per channel 195 V
- Max. output current per channel 83 A peak
- Max. Output Power 2 ohms 4 ohms 8 ohms 16 ohms
- Per ch. (both ch.’s driven) 7000 W 4400 W 2350 W 1200 W
- Bridged per ch. n.r. 3) 14000 W 8800 W 4700 W
- Performance with Gain: 35 dB and VPL: 195 V
- THD 20 Hz - 20 kHz for 1 W <0.1%
- THD at 1 kHz and 1 dB below clipping <0.05%
- Signal To Noise Ratio >112 dBA
- Channel separation (Crosstalk) at 1 kHz >70 dB
- Frequency response (1 W into 8 ohms) +0/-3 dB 2 Hz - 34.2 kHz
- Input impedance 20 kOhm
- Input Common Mode Rejection, CMR 54 dB
- Output impedance @ 100 Hz 56 mOhm
- Voltage Peak Limiter (VPL), max. peak output
- VPL, selectable per ch. 195, 170, 140, 116, 100, 80, 66, 54 V
- VPL, selectable when bridged 1) 390, 340, 280, 232, 200, 160, 132, 108 V
- Voltage Peak Limiter mode (per ch.) Hard / Soft
- Gain and Level
- Amplifier gain selectable (all channels) 1)
- – rear-panel switches
- 23, 26, 29, 32, 35, 38, 41, 44 dB
- Default gain 38 dB
- Level adjustment (per ch.) Front-panel potentiometer, 31 position detented from -inf to 0 dB
- Connectors and Switches
- Input connectors (per ch.) 3-pin XLR, electronically balanced
- Output connectors (per ch.) Binding Posts 2-pole
- Output bridge mode A+B - Ch. A is signal input source
- NomadLink network On board, 2 x RJ45 EtherCon® connectors, IN and OUT
- Intelligent fans (on/off) Yes, depending on presence of output signal
- Power on/off and Remote enable on/off Individual switches on front-panel
- Cooling Two fans, front-to-rear airflow, temperature controlled speed
- Front-panel indicators:
- Common NomadLink Network; Power Average Limiter (PAL) 2); Power on
- Per channel Signal present / High-impedance; -20 dB, -15 dB, -10 dB and -4 dB output signal;
- Voltage Peak Limiter (VPL); Current Peak Limiter (CPL); Very High Frequency (VHF); High temperature; Fault; Mute
- Power
- Operating voltage, 230 V / 115 V nominal 4) 130-265 V / 65-135 V
- Minimum power-up voltage, 230 V / 115 V 171 V / 85 V
- Power Average Limiter (PAL) 2) Yes
- Soft start / Inrush Current Draw Yes / max. 5 A
- Mains connector 230 V CE: 16 A, CEE7; 115 V ETL: 30 A Twist lock
- Dimensions (W/H/D) W: 483 mm (19”), H: 88 mm (2 U), Overall D: 396 mm (15.6”), Mounting D: 358 mm (14.1”)
- Weight 12 kg (26.4 lbs.)