LAB GRUPPEN เพาเวอร์แอมป์ FP 4000 เครื่องขยายเสียง กำลังวัตต์สูง delivers a total of 4000 W (2 x 2000 W @ 2 ohms) in only 2U
A Benchmark For Touring Amplification
Over the past decade, the tight and transparent sound of
Lab.gruppen touring amplifiers has earned the praise of renowned
FOH engineers and leading sound rental companies worldwide.
The FP+ Series model FP 4000 continues this tradition. At the core
of the FP 4000’s performance is the patented Class TD output stage,
a breakthrough amplifier topology that approaches the exceptional
efficiency of Class D while retaining the sonic purity of proven Class B
technology designs. Further contributing to the remarkable efficiency
of the FP 4000 is a Regulated Switch Mode Power Supply (R.SMPS),
which gives the added benefit of stabilizing rail voltages to the output
even with wide fluctuations of mains voltage. A highly refined and
updated circuit layout optimizes the interaction of R.SMPS and Class
TD to produce the high power density of the FP 4000.
To keep its cool under extreme demands, the FP 4000 relies on
Lab.gruppen’s proprietary Intercooler. This innovation uses thousands of copper fins to multiply the exposed heatsink surface’s rapid
heat dissipation. Also, all output devices are mounted transverse to
the airflow for uniform cooling. As a result, the FP 4000 delivers
Lab.gruppen’s’ trademark “all the power, all the time” with no
degradation of sonic performance.
To maximize headroom in any application, the FP 4000 offers
adjustable input gain along with Lab.gruppen’s exclusive Voltage Peak
Limiter (VPL). Adjustable on a per-channel basis, VPL optimizes the
output for any load, from a single massive subwoofer to a series of
HF compression drivers.
The comprehensive warning and protection features on the
FP 4000 safeguard output circuits and connected loads while also
extending amplifier life and minimizing the chance of service interuptions. Whether it’s a matter of faulty wiring, improper use, or extreme
ambient temperatures, the FP 4000 gives clear indication of any problems. Automatic protection measures engage only at critical thresholds. Operating conditions are re-checked every six seconds and, if
a fault is detected, normal operation is resumed when measurements
return to nominal.
The FP 4000 is shipped with a NomadLink network interface as
standard. In conjunction with DeviceControl software, NomadLink
allows comprehensive monitoring of amplifier status (including fault
or warning indications) and also enables remote control of power on/
off, channel mute, and channel solo functions. NomadLink is compatible with popular third-party control platforms; a separate NLB 60E
NomadLink Bridge & Network Controller is required.
Specifications FP 4000
General
Number of channels 2
Peak total output both channels driven 4000 W
Peak output voltage per channel 121 V
Max. output current per channel 50 A peak
Max. Output Power 2 ohms 4 ohms 8 ohms 16 ohms
Per ch. (both ch.’s driven) 2000 W 1600 W 800 W 400 W
Bridged per ch. n.r. 3) 4600 W 3200 W 1600 W
Performance with Gain: 35 dB and VPL: 150 V
THD 20 Hz - 20 kHz for 1 W <0.1%
THD at 1 kHz and 1 dB below clipping <0.05%
Signal To Noise Ratio >112 dBA
Channel separation (Crosstalk) at 1 kHz >70 dB
Frequency response (1 W into 8 ohms) +0/-3 dB 2 Hz - 34.2 kHz
Input impedance 20 kOhm
Input Common Mode Rejection, CMR 45 dB
Output impedance @ 100 Hz 56 mOhm
Voltage Peak Limiter (VPL), max. peak output
VPL, selectable per ch. 121, 101, 83, 70, 56, 47, 38 V
VPL, selectable when bridged 1) 242, 202, 166, 140, 112, 94, 76 V
Voltage Peak Limiter mode (per ch.) Hard / Soft
Gain and Level
Amplifier gain selectable (all channels) 1)
– rear-panel switches
23, 26, 29, 32, 35, 38, 41, 44 dB
Default gain 38 dB
Level adjustment (per ch.) Front-panel potentiometer, 31 position detented from -inf to 0 dB
Connectors and Switches
Input connectors (per ch.) 3-pin XLR, electronically balanced
Output connectors (per ch.) Neutrik Speakon or Binding Posts (must be specified upon order)
Output bridge mode A+B - Ch. A is signal input source
NomadLink® network On board, 2 x RJ45 EtherCon connectors, IN and OUT
Intelligent fans (on/off) Yes, depending on presence of output signal
Power on/off and Remote enable on/off Individual switches on front-panel
Cooling Two fans, front-to-rear airflow, temperature controlled speed
Front-panel indicators:
Common NomadLink Network; Power Average Limiter (PAL) 2); Power on
Per channel Signal present / High-impedance; -20 dB, -15 dB, -10 dB and -4 dB output signal;
Voltage Peak Limiter (VPL); Current Peak Limiter (CPL); Very High Frequency (VHF); High temperature; Fault; Mute
Power
Operating voltage, 230 V / 115 V nominal 4) 130-265 V / 65-135 V
Minimum power-up voltage, 230 V / 115 V 171 V / 85 V
Power Average Limiter (PAL) 2) Yes
Soft start / Inrush Current Draw Yes / max. 5 A
Mains connector 230 V CE: 16 A, CEE7; 115 V ETL: 20 A / NEMA 5-20P
Dimensions (W/H/D) W: 483 mm (19”), H: 88 mm (2 U), Overall D: 396 mm (15.6”), Mounting D: 358 mm (14.1”)
Weight 12 kg (26.4 lbs.)
Finish Black painted steel chassis with gray painted steel front
Approvals CE, ANSI/UL 60065 (ETL), CSA C22.2 NO. 60065, FCC