| Model |
PT-DS12KE |
| Power supply |
120 V, 220-240 V AC, 50/60 Hz |
| Power consumption |
120 V AC |
980 W (1,010 VA)
(0.2 W with standby mode set to eco.*1
6 W with standby mode set to normal. Both with fan stopped.) |
| 220-240 V AC |
950 W (980 VA)
(0.3 W with standby mode set to eco.*1
9 W with standby mode set to normal. Both with fan stopped.) |
| Dissipation BTU |
120 V: 3,345 BTU/hour (without light output: 3,181 BTU/hour).
220–240 V: 3,242 BTU/hour (without light output: 3,079 BTU/hour) |
| DLP™ chip |
Panel size |
24.1 mm (0.95 in) diagonal (4:3 aspect ratio) |
| Display method |
DLP™ chip x 3, DLP™ projection system |
| Pixels |
1,470,000 (1,400 x 1,050) x 3, total of 4,410,000 pixels |
| Lens |
Optional powered zoom/focus and fixed-focus lenses |
| Lamp |
380 W UHM lamps (HIGH mode) x 2 |
| Screen size (diagonal) |
1.78 –25.4 m (70–1,000 in), 1.78 –15.24 m (70–600 in) with the ET-D75LE8, 4:3 aspect ratio |
| Brightness*2 |
12,000 lm*3 (dual-lamp) |
| Center-to-corner uniformity*2 |
0.9 |
| Contrast*2 |
10,000:1 (full on/off, with DYNAMIC IRIS set to "3") |
| Resolution |
1,400 x 1,050 pixels (Input signals that exceed this resolution will be converted to 1,400 x 1,050 pixels.) |
| Scanning frequency |
SDI |
Dual-link HD-SDI |
SMPTE ST 372 compliant, [RGB 4:4:4 12-bit /10-bit] 1080/50i, 1080/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p, [X´Y´Z´ 4:4:4 12-bit] 2,048 x 1,080/24p, 2,048 x 1,080/24sF |
| 3G-SDI |
SMPTE ST 424 compliant, [RGB 4:4:4 12-bit /10-bit] 1080/50i, 1080/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p [YPBPR 4:2:2 10-bit] 1080/50p, 1080/60p, |
| HD-SDI |
SMPTE ST 292 compliant, [YCBCR 4:2:2 10-bit] 720/50p, 720/60p, 1035/60i, 1080/50i, 1080/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p |
| SD-SDI |
SMPTE ST 259 compliant, [YCBCR 4:2:2 10-bit] 480i, 576i |
| HDMI/DVI-D |
480p, 576p, 720/60p, 720/50p, 1080/60i, 1080/50i, 1080/24p, 1080/24sF, 1080/25p, 1080/30p, 1080/60p, 1080/50p, VGA (640 x 480)–WUXGA*4 (1,920 x 1,200), compatible with non-interlaced signals only, dot clock: 25–162 MHz |
| RGB |
fH: 15–100 kHz, fV: 24–120 Hz, dot clock: 20–162 MHz |
| YPBPR (YCBCR) |
fH: 15.75 kHz, fV: 60 Hz [480i(525i)]
fH: 15.63 kHz, fV: 50 Hz [576i(625i)]
fH: 45.00 kHz, fV: 60 Hz [720(750)/60p]
fH: 33.75 kHz, fV: 60 Hz [1035/60i]
fH: 28.13 kHz, fV: 50 Hz [1080(1125)/50i]
fH: 27.00 kHz, fV: 24 Hz [1080/24p]
fH: 33.75 kHz, fV: 30 Hz [1080/30p]
fH: 56.25 kHz, fV: 50 Hz [1080/50p]
fH: 31.50 kHz, fV: 60 Hz [480p(525p)]
fH: 31.25 kHz, fV: 50 Hz [576p(625p)]
fH: 37.50 kHz, fV: 50 Hz [720(750)/50p]
fH: 33.75 kHz, fV: 60 Hz [1080(1125)/60i]
fH: 28.13 kHz, fV: 25 Hz [1080/25p]
fH: 27.00 kHz, fV: 48 Hz [1080/24sF]
fH: 67.50 kHz, fV: 60 Hz [1080/60p] |
| Video/Y/C |
fH: 15.75 kHz, fV: 60 Hz [NTSC/NTSC4.43/PAL-M/PAL60],
fH: 15.63 kHz, fV: 50 Hz [PAL/PAL-N/SECAM] |
| Optical axis shift*5 |
Vertical |
±50 % (±40 % with the ET-D75LE6) from center of screen (powered) |
| Horizontal |
±30 % (±20 % with the ET-D75LE6) from center of screen (powered) |
| Keystone correction range |
Vertical: ±40°*6, horizontal: ±15° |
| Keystone correction range with optional Upgrade Kit ET-UK20 |
Vertical ±40° and horizontal ±40° with the ET-D75LE1/LE2/LE10/LE20, vertical ±45° and horizontal ±40° with the ET-D75LE3/LE4/LE30/LE40, vertical ±22° and horizontal ±15° with the ET-D75LE5/LE50, vertical ±28° and horizontal ±15° with the ET-D75LE6 |
| Installation |
Ceiling/floor, front /rear, portrait*7 |
| Terminals |
SDI 1 IN |
BNC x 1 (3G/HD/SD-SDI) |
| SDI 2 IN |
BNC x 1 (HD/SD-SDI) |
| 3D SYNC IN/OUT |
BNC x 1 (3D timing signal) |
| 3D SYNC OUT |
BNC x 1 (3D timing signal) |
| DVI-D IN |
DVI-D 24-pin x 1 (DVI 1.0 compliant, compatible with HDCP, compatible with single link only) |
| HDMI IN |
HDMI 19-pin x 1 (Deep Color, compatible with HDCP) |
| RGB 1 IN |
BNC x 5 (RGB/YPBPR/YCBCR/YC x 1) |
| RGB 2 IN |
D-Sub HD 15-pin (female) x 1 (RGB/YPBPR/YCBCR x 1) |
| VIDEO IN |
BNC x 1 (composite video) |
| SERIAL IN |
D-sub 9-pin (female) x 1 for external control (RS-232C compliant) |
| SERIAL OUT |
D-sub 9-pin (male) x 1 for link control |
| REMOTE 1 IN |
M3 x 1 for wired remote control |
| REMOTE 1 OUT |
M3 x 1 for link control (for wired remote control) |
| REMOTE 2 IN |
D-sub 9-pin (female) x 1 for external control (parallel) |
| LAN |
RJ-45 x 1 (for network connection, 10Base-T/100Base-TX, compliant with PJLink™) |
| Cabinet materials |
Molded plastic |
| Dimensions (W x H x D) |
530 x 200*8 x 548.5 mm (20-7/8 x 7-7/8*8 x 21-19/32 in) (optional lens not included) |
| Weight*9 |
Approximately 24 kg (52.9 lbs) (optional lens not included) |
| Operation noise*2 |
45 dB (dual lamp operation with lamp HIGH mode), 43 dB (dual lamp operation with lamp MIDDLE mode), 37 dB (dual lamp operation with lamp ECO mode) |
| Operating environment |
Operating temperature: 0–45°C (32–113°F)*10, operating humidity: 10–80 % (no condensation) |
| Applicable software |
Logo Transfer Software, Multi Projector Monitoring & Control Software, Geometry Manager Pro (included in the ET-UK20) |
| Supplied accessories |
Power cord with secure lock, wireless/wired remote control unit, batteries (R6/AA type x 2) |
