PERFORMANCE |
System Type |
3-Way Full Range - Point Source |
Frequency Response (-3dB) 1 |
115Hz - 23kHz |
Frequency Range (-10dB) 1 |
90Hz - 27kHz |
Dispersion (-6dB) |
60 degrees conical |
Driver Complement |
|
LF |
2 x 300mm (12.00”) LF Transducers, Semi Horn Loaded |
MF/HF |
Dual Concentric™ Compression driver loaded into a single PSW™ Waveguide |
Crossover Frequency |
450Hz (DSP Generated) 7kHz (passive) |
Directivity Factor (Q) |
21.2 averaged 1kHz to 10kHz |
Directivity Index (DI) |
13.3 averaged 1kHz to 10kHz |
Rated Maximum SPL |
|
LF |
134dB (average) 140dB (peak) |
MF/HF |
138dB (average) 144dB (peak) |
Notes |
1. Average over stated bandwidth. Measured at 3 metres on axis, then referred to 1 metre |
|
2. Unweighted pink noise input, measured at 3 metres in an anechoic chamber, then referred to 1 metre |
|
A full range of measurements, performance data, and Ease™ Data can be downloaded from www.tannoy.com |
|
Tannoy operates a policy of continuous research and development. The introduction of new materials or manufacturing methods will always equal or exceed the published specifications, which Tannoy reserves the right to alter without prior notification |
Construction |
|
Enclosure |
18mm (0.71") birch plywood. Vented and internally braced. |
Finish |
Textured black paint. |
|
Powder coated perforated steel grille |
Connectors |
1 x female XLR (input) |
|
1 x male XLR (link) |
|
1 x RJ45 (network in) |
|
1x RJ45 (network link) |
|
1 x Neutrik Powercon |
|
1 x Powercon OUT |
Controls & Indicators |
LED on front of cabinet behind grille.
|
|
Power LED (blue) |
|
Signal LED (green) |
|
Limit LED (red) |
|
User DSP - defeat switch |
|
Power switch |
Fittings |
8 x Recessed carrying handles |
|
12 x M10 flying inserts |
|
Coupling bracket inserts for aligning devices in clusters |
Dimensions |
925mm x 620mm x 502mm (36.42" x 24.41" x 19.76") |
Weight |
86.5Kg (98.5Kg with dolly)
|
Electronics |
|
Efficiency |
>85% typically |
Damping Factor |
120 ref 8 Ohms |
Distortion |
<0.05% @ 1kHz -3dB output (22kHz bandwidth) |
Input Impedance |
5.6kOhms unbalanced, 11.2kOhms balanced |
Output Power (Programme) |
LF - 800W |
|
MF/HF - 800W (limited to 400W) |
Input Sensitivity |
1.4V ( 5.5dBu) |
System Type |
Dual channel Class D |
DSP system |
|
Comms Facilities |
Firmware updatable and selected parameters editable |
Communications |
Serial - RS485 Proprietary message format |
Dynamic Range |
112dB(A) typical |
DSP |
3rd generation SHARC |
Sampling Frequency |
96kHz 24 bit A/D-D/A word length |
Format |
1 IN - 2 OUT |
PSU Specifications |
|
Input Connector |
Locking Neutrik Powercon |
Voltage Selection |
Automatic (115 / 230V, 45 - 65Hz) |
Type |
High current, high frequency switch mode |
Efficiency |
>90% typical |
Input voltage |
100v / 115v / 230v nominal /-10% |
Mains fuse |
External |
Fuse type |
T10AT |
Other features |
Automatic soft start |
Current Draw |
115V 230V |
Startup (inrush) |
3.5A 1.9A |
idle |
1.0A 0.56A |
In PowerSave Mode |
|
Max |
3.5A 1.7A |